PontiacGroup.com
INSTRUCTIONS FOR PART # 1328 A KIT TO ADAPT A 1964-72 A-BODY 10 OR 12 BOLT REAR AXLE INTO A 1978-87 G-BODY CHASSIS MALIBU, CUTLASS, MONTE CARLO, REGAL, G.N., GRAND PRIX
THIS KIT IS DESIGNED TO ADAPT A 1964- 72 GM A BODY 10 OR 12 BOLT REAR AXLE ASSEMBLY INTO A 1978-87 GM G-BODY CHASSIS. THE ONLY THING THAT WILL VARY ON THE REAR AXLE WOULD BE THE WIDTHS FROM YEAR TO YEAR. ALL THE MOUNTING BRACKETS WOULD BE THE SAME FOR 1964-72. IF YOU CAN'T FIND ONE THE RIGHT WIDTH, YOU CAN USE A WHEEL WITH A DIFFERENT OFFSET OR HAVE THE HOUSING AND AXLES SHORTENED.
1.
Jack up the car and place on four (4) jack stands.
2.
Soak all bolts on the upper and lower arms, sway bar, shocks and brake line with
penetrating oil if necessary.
3.
Unbolt the lower shock mounts. Then lower the rear end down and remove the coil
spring, unhook the brake line and emergency brake cables. Then unbolt the upper
and lower control arms from the chassis and remove the rear end.
4.
Before installing the A-body rear end, this would be a good time to install new
upper bushings. Next you will have
to use a torch and grinder to remove the stock spring seats from the axle tubes
and weld on the new ones supplied with the kit. Weld them in place using the
dimensions shown in Figure 1.
This would also be the time to weld on the shock mounts as shown in Figure
6 or you can do it after the rear end is installed. That's up to you.
5.
Install the upper control arms into the chassis left and right as shown in Figure
2 using 12mm x 90mm bolts, lock washers and nuts supplied with the kit.
6.
Using a floor jack, lift the rear end in place into the upper control arms and
install 1/2" x 3 1/2" bolts, lock washers and nuts supplied with the
kit. Do NOT tighten.
7.
Next install the lower control arms and brackets using the 12mm x 90mm bolts in
the front and the 1/2" x 3 1/2" bolts in the rear with the lock
washers and nuts supplied in the kit as shown in Figures
3, Figure 4 and Figure
5. Do NOT tighten. The lower arms are made as lefts and rights and that is
the only way they fit. If you
install them on the wrong side, the rear bolt holes will not line up with the
bracket holes.
8.
With everything bolted in place, you can reinstall the coil springs, then jack
the rear end up and install the shocks and wheels.
9.
Now the next thing is to check and set the pinion angle. To do this you will
have to take the car off the jack stands and place the car on four (4) blocks or
car ramps or equal height (one under each wheel). This is so the suspension is
loaded just the way is it driven. Now you will need to check and/or set the
pinion angle as described in the attached instruction sheet on setting the
pinion angle. To do this operation you will need a magnetic protractor (angle
finder), which you can get from a local discount store (K-Mart, Wal-Mart,
Sears). If you need more pinion angle, you need to remove plates A and grind or
machine a relief where the plate touches the axle tube (remove about 1/8"
at a time). Then reassemble and check the pinion angle until you get the desired
4-6 degrees including the angle. If you needed less pinion angle, use a shim
between the plate and axle tube to get the desired pinion angle.
10.
With the pinion angle set you can tighten all the bolts. Then drill hole 4 as
shown in Figures 3 and Figure
4 with a 1/2" drill and install the 2 1/2" x 1 1/4" bolts,
lock washers and nuts. Torque all 1/2" bolts to 100 ft/lbs. Torque all12mm
bolts to 75 ft/lbs.
11.
Give all grease fittings a shot of grease. Then reconnect the emergency brake
cables and brake lines. Bleed the lines.
If
you have any comments write:
Southside Machine Co., Inc.
P.
O. Box 617
Smithville, OH 44677
PINION
ANGLE AND OTHER CHASSIS TUNING TIPS
NOTE: THIS DRAWING IS AN EXAGGERATION, YOUR PINION ANGLE WILL NOT BE THIS RADICAL.
Pinion
angle affects the efficiency of the power transmission from the drive shaft to
the rear end. The pinion angle is
the spread between the pinion centerline and the drive shaft centerline. For
maximum performance, the ideal is to have a slight pinion down angle (min. 2
degrees) under full power.
Obviously,
the pinion angle changes as power is applied and the axle housing begins to
twist as the pinion tries to drive the ring gear. Rear axle wind-up can take some of the initial energy or
"hit" away from the launch. As a general rule, a leaf spring rear
suspension should have between 5-7 degrees of static pinion angle (angle down);
and a factory four-link should be set at 4-6 degrees.
Keep
in mind that these pinion angles are for competition. If you primarily drive
your car on the street, you shouldn't have more than a 5 degree angle maximum.
The U-joints are designed to run at this angle, which allows the cups to rotate
avoiding premature wear and failure. This doesn't affect leaf spring suspension
since it runs well within this tolerance.
You
will need to have the car level on four (4) car ramps or blocks of equal heights
so you have room to work under the car when checking the pinion angle. Also,
both the front and rear suspension need to be loaded to get accurate readings.
The height of the rear end relative to the rest of the driveline will affect the
pinion angle. Using an angle finder, which is a tool that combines a bubble
level and a protractor, to determine the correct pinion angle for your car.
Position the angle finder on the drive shaft and record the measurement. Then
place the angle finder on the pinion (the U-joint yoke rotated to vertical
position will give an accurate reading) and record the measurement. The pinion
angle is a combination of the two measurements.
The
following are fine tuning tips for your suspension:
You
can purchase shocks that are 3-position adjustable for both front and rear
applications. These shocks are available from your local speed shop or mail
order supplier. If you can't find shocks designed for your specific application,
you'll have to check in a shock catalog for O.E. applications. You may have to
use shocks from another make or model that has the same mounts at each end and
the same length, or an inch or two longer. This won't hurt, because it allows
for more suspension travel, so you don't hit the end of your shock travel and
pull the rear wheels off the ground.
Coil spring cars, use 90/10 front shocks on small block cars, 80/20 or 70/30 on big block cars and high horsepower small blocks. On short wheel base cars like Mustangs and Capri's, use the 80/20 or 70/30 settings. Use 50/50 rear shocks along with an air bag (4-8 lbs air) in the right rear coil spring only. This you will have to play with to find the best setting for your car. The air bag is used to counteract the engine torque wanting to lift the left front corner.
CHASSIS
WORK
To
help the effects of the lift bars, especially on unibody cars, you can greatly
improve the chassis reaction by tying the sub frame together with the sub frame
connectors. Also a minimum of six-point cage to stiffen the chassis up would
help. That way the chassis is not absorbing the energy or hit of the bars. And
all that energy will be directed to the tires to help lay out a bigger
footprint.
If
you have any comments write:
Southside
Machine Co., Inc.
P.
O. Box 617
Smithville,
OH 44677
Or
for questions, call our technician, Louie, between 9 AM and 12 noon, Monday
through Thursday at 330-669-9725. FAX
to: 330-435-4630. Email at: ssmcoinc@aol.com
or visit the website at www.ssmliftbars.com
Copyright 2003
SouthSideMachine Co, Inc.